/ Toyota / Tacoma / sticking clutch? 3 sticking clutch? 5 Report; Follow. Had the same problem with my 2007 Tacoma. Don't know if the '95 uses the same type system, Check if the master clutch reservoir is full. If it is not, you could have a leak. 5 speed transmission wont go into gear when clutch is pressed and there is no reistance on. Consult your owner’s manual to find your manufacturer’s recommendations on clutch lifespan. Replacing A Clutch. While a clutch replacement is within the scope of a home repair for a knowledgeable car owner, it is one of the most complex auto repair jobs that can be done at home.
By: Bill O'Laverty. May, 2002
The dust inside the bellhousing produced by the clutch disc can be hazardous to breathe in. Do not blow it or used compressed air, only use brake cleaner to clean it out, and be sure to work in a well-ventilated area.
Parts and Tools Needed:
Remove the shift levers. The transmission shift lever is removed by pressing down on the metal collar and turning it left, then it will just slide out. For the 4wd shift lever, simply squeeze the end of the snap rings together and pull it out.
Depending on your suspension, you may need to jack up the vehicle and place it on jackstands. I had both a body and a suspension lift so I had plenty of clearance to work underneath with jacking it.
![]()
Next, I removed the wire harness after unplugging everything. One of the most difficult times I had with this project was removing the plastic clips holding in the wire harness, I broke a couple of them.
Free eyelash extension training manual. Remove both front and rear driveshafts. For optimum balancing upon reinstallation, be sure you mark the driveshaft against the flange so that they can be reassembled in the same position. The rear driveshaft only has to be disconnected from the transfer case, then you can slide it out of the way.
Remove all plumbing for the clutch hydraulics. It does not need to be bled if you do not disconnect the hoses, just undo the clamps from the bellhousing. Unbolt the clutch release cylinder. Double check the entire transmission and make sure nothing is left conected to it (speedo cables, etc.)
Remove the clutch cover on the forward bottom side of the transmission. There are four bolts that hold it on, I broke the heads off two of the bolts trying to take them out and had to drill and tap the holes once the transmission was out.
Jack up the transmission with a transmission jack (I rented one at a local rent-all place for $5 a day.) It should be placed as close to the crossmember as possible to get it under the center of gravity. Unbolt and remove the crossmember.
95 Toyota Tacoma Manual Transmission Cluch And Fork For Sale
At this point you are ready to remove the transmission to engine bolts, however with the transfer case still on you need to move the transmission jack further back so it doesn't tip back. I supported the transmission with a jackstand and a block of wood then moved the jack back under where the crossmember was. Remove all bolts, including the two going to the starter. After the bolts are removed, slide the transmission straight back until the input shaft is clear, then lower it. If you have trouble sliding it back then you're probably not coming straight back with it. Honda crosstour service manual download. Make sure the transmission stays level and straight as it comes back.
Unbolt the pressure plate and remove the clutch disk. You will have to undo each bolt a little at a time, you will feel the spring pressure being relieved as you do this. Use a criss-cross pattern as you undo the bolts.
95 Toyota Tacoma Manual Transmission Cluch And Fork Tx
While not required, it is recommended that you remove the flywheel and have it resurfaced at this point. Mark the flywheel in the center with the crankshaft to ensure you reinstall it in the same position. Most transmission shops can resurface it for you. Reinstall and torque the bolts to 19 ft lbs, followed by an additional 90 degree turn. Use Loctite on all bolts you reinstall. Clean the surface of flywheel with brake cleaner to prevent any contaminants from ruining the surface.
![]()
Remove the pilot bearing either before, during, or after flywheel removal. I used the age-old trick of packing the back of it with grease, then hammer in a bolt that just fits inside the bearing. The pressure from the grease will drive out the bearing. It's messy, but this works like a charm.
Clean out all of the grease and install a new pilot bearing. I just use a socket that is the same size as the bearing to drive in.
Clean the machined surface of the pressure plate with brake cleaner. Position the clutch disc on the flywheel and insert the clutch alignment tool to hold the disc in place. The side of the disc that has the springs sticking out goes towards the transmission. Install the pressure plate and finger tighten all bolts (use Loctite). Make sure the alignment tool is installed all of the way. Tighten the pressure plate bolts in a criss-cross pattern, you will feel the spring pressure build up as you tighten them. Torque to 14 ft lbs.
Inside the bellhousing on the transmission, snap off the spring on the throwout bearing fork and remove the fork and bearing. Clean out the bellhousing with brake cleaner. Lube all contact points on the fork and the input shaft with high temp grease. Install the new throwout bearing and fork in bellhousing.
Now you're ready to put it all back together. No special words of wisdom here, it's just the reverse of what you did for removal. Just remember clean parts are happy parts and Loctite, Loctite, Loctite! The torque for the transmission to engine bolts are 53 ft. lbs. This job took me about 6 hours working alone.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |